The motor power lead should be positioned tightly against the end plate. Create a drip loop in the cable to prevent water from running down the cable and into the motor see Drawing C. Ensure the pillars, lintel and header are free from sharp objects or bumps before positioning the frame.
Obstacles such as these may twist the guides or distort the fascia.. The end plate pegs are not designed to carry the weight of the door. Slide the locking straps onto the last slat of the curtain while the last slat hands over the shaft. Line the clamps of the Selve lock with cutting hole Y see Drawing C.
Turn slot X by using a coin in direction of arrow as far as it will go. Attention - when turning the slot X the clip snaps into place. In addition, please ensure that you use two 4. The motor can be damaged if other screws are used. Once the Selve locking straps are attached, use manual override loosely to take the shutter half way up. When connecting to an electricity source, the limitations of the Low Voltage Directive should be observed.
Connections to the V mains supply must be made by a competent person. The arrangement and positioning of the electrical control panel should be such that the operator can see the door, and should be on the motor side. Please refer to the individual control panel instructions for mounting and commissioning. The instructions include important safety information and should be left with the end user. It is recommended to attach the motor to a test lead.
Please refer to separate limit setting instructions attached to the barrel. Fully press in limit switch to activate. The work area under the door is clear and safe, with appropriate signage if in a public area. You and anyone assisting you are wearing appropriate safety gear i. Installation Step 1 — Brackets 1. Measure and mark the door width on each side of the doorway, adding 50mm for the inside line of the bracket. Hold the bracket and mark three hole positions.
Then drill the holes and bolt the bracket into position. Use the laser level to mark the height of the second bracket on the other side of the doorway. Employing safe lifting techniques, lift the rolled up door onto the brackets, facing so that it will roll down the front side.
Make sure the floating axle is free and centred by rotating it a quarter turn in either direction then releasing. Once the centre is found, make a clear mark on the axle against the hub for future reference. Loosely fit the supplied saddle, U bolts, nuts, washers and keepers. Centre the door with the opening, and the axle with the door. Do this by lining up the previous marks with the hub before lifting the axle and door together until centred with the opening. Step 2 - Springs 1.
Firmly secure the axle to the brackets with the U bolts and lock tightly with washers and nuts considerable tension will be applied when the spring is tensioned to ensure they are well tightened.
Apply tension to the spring by rotating the door two times in a forward direction the amount of tension required for best operation will vary with individual doors. Hold the door while your assistant cuts the plastic straps hold firmly to prevent loss of tension. Pull the door curtain down slowly and carefully position the wooden chock, which will help to hold the door until the tracks are fitted.
Step 3 - Tracks 1. Pull the door down and check that it overlaps equally on both sides of the doorway. Slide the first track over the edge of one side of the door and fix the track loosely to the wall with the fasteners supplied. Just a quick note to say thank you for the excellent service your company gave from order placement to delivery. I have fitted the garage door and I am extremely happy with it and it has added a touch Paul Waterfield.
Thanks for getting my door fixed and a good quality service. My wife as just called me at work and said they the engineers did a good job. I wouldn't hesitate in recommending your company to friends Simon Truscott. Many thanks for the speedy delivery of my garage door can I say what a brilliant garage door it is and was so simple to fit and wire up think it took me under 2hours and that includes taking Roger and Barbara Page.
Just a quick email, to thank you for supplying the roller doors for our new double garage, we are very pleased with them and the fitters were quick, efficient and polite.
We thought the price Terrence R Winter. Just a short thank you for your superb and highly efficient customer contact when I came to collect my door the service I experienced I have not seen any where for a very long time I was not Jane Baker. I just wanted to thank you so much for your help in purchasing a new remote for the garage door.
All of you have been fantastic from your help at the beginning to the actual pairing of the fob See more client testimonials Top. Call Call Calls are recorded Basket. Christmas opening times Our offices will be shut from 24th December Christmas Eve , until the 4th January. Accessories View all. Support View all. About Us Learn about Rollerdor and what makes us unique Find out more.
Gallery View our products and previous installations View Gallery. News Read the latest company and industry news View Posts. Order your new garage door using our online ordering system Try it now. Contact Us T: E: sales rollerdor. Tutorials Rollerdor Overview Click to watch video Play video.
0コメント